Produkty > uaktualnienie programu cadvilla do wersji 6

cadvilla — uaktualnienie i zamiana

cadvilla — uaktualnienie do wersji 6 z możliwością zamówienia

Poniżej znajdują się wszystkie ceny uaktualnienia programu cadvilla do wersji 6. Jest to obszerna aktualizacja z wieloma poprawkami i dodatkowymi usługami.

  Wersje — uaktualnienie z — do Cena Pobieranie **    
  cadvilla basic2/3/4/5 do cadvilla basic EUR 13,95* ok. 1,4 GB Bestellung von Update cadvilla basic  
  cadvilla basic plus 2/3/4/5 do cadvilla basic plus EUR 23,95* ok. 1,4 GB Bestellung von Update cadvilla basic plus  
  cadvilla professional 2/3/4/5 do cadvilla professional zamiast € 124,50
EUR 61,95*
ok. 1,4 GB Bestellung von Update cadvilla professional  
  cadvilla professional plus 2/3/4/5 do cadvilla professional plus zamiast € 149,50
EUR 75,95*
ok. 1,4 GB Bestellung von Update cadvilla professional plus  
  * Wszystkie ceny zawierają VAT, Specjalna promocja do 31.08.2017 r. włącznie
** Opcjonalnie można zakupić płytę CD za cenę 9,95 EUR podczas zamawiania

cadvilla — zamiana na obszerniejszą wersję z możliwością zamówienia

Jeśli użytkownik chce w ramach uaktualnienia dokonać zamiany na produkt wyższego poziomu:

  Zamiana produktu z — na Cena Pobieranie **    
  cadvilla basic 2/3/4/5/6 na cadvilla professional zamiast € 220,00
EUR 105,95*
ok. 1,4 GB cadvilla professional kaufen  
  cadvilla basic plus 2/3/4/5/6 na cadvilla professional zamiast € 199,00
EUR   93,95*
ok. 1,4 GB cadvilla professional kaufen  
  cadvilla basic plus 2/3/4/5/6 na cadvilla professional plus zamiast € 375,00
EUR 188,00*
ok. 1,4 GB cadvilla professional plus kaufen  
  cadvilla professional 2/3/4/5/6 na cadvilla professional plus zamiast € 176,00
EUR 143,00*
ok. 1,4 GB cadvilla professional plus kaufen  
  * Wszystkie ceny zawierają VAT, Specjalna promocja do 31.08.2017 r. włącznie
** Opcjonalnie można zakupić płytę CD za cenę 9,95 EUR podczas zamawiania


Dodatkowe funkcje wersji 6.x.x.x

Dodatkowe funkcje programu cadvilla wersja 6 przedstawione w poniższej tabeli stanowią tylko najważniejsze nowości. Oczywiście dokonano wielu innych mniejszych zmian i uzupełnień, a także korekty niedociągnięć.

Legenda dotycząca poniższej tabeli:

yes - Wersja zawiera tę funkcję.
no - Wersja nie zawiera tej funkcji.

help - Objaśnienia i informacje szczegółowe dotyczące danej pozycji można otrzymać po bezpośrednim kliknięciu odpowiedniego wiersza.

Dodatkowe funkcje wersji 6 cadvilla basic cadvilla basic plus cadvilla professional cadvilla professional plus

Details  Mirroring 2D symbols ... moreyesyesyesyes
Mirroring 2D symbolsThere are two tools for mirroring 2D symbols that appear in the selection tool bar once a 2D graphic symbol has been selected. Mirroring a 2D symbol can be done on any specified axis or at the center point of the 2D symbol.

A distinction is made between two types of mirroring
- Basic mirroring
- Mirroring with a copy. In case of mirroring with a copy, the initial element is preserved and a new, mirrored 2D symbol will be created.

Mirroring still works even after selecting multiple 2D graphic symbols. After specifying the type of mirroring, all selected 2D graphic symbols will be mirrored at the same time.
Details  Mirroring 3D objects ... moreyesyesyesyes
Mirroring 3D objectsMirroring a 3D object can be done at the center point of the 3D object or on a defined mirror axis.
After selecting a 3D object, there are two mirroring tools available in the selection toolbar.

- Basic mirroring of a 3D object
- Obtaining a selected 3D object and creating a new, mirrored 3D object on the mirror axis.

Mirroring works even after selecting multiple 3D graphic symbols. Select multiple 3D objects and determine the type of mirroring in the selection toolbar. Afterwards, all selected 3D objects will be mirrored in one step.
Details  380 new 2D graphic symbols ... moreyesyesyesyes
380 new 2D graphic symbolsAs of version 6, there are 380 new 2D graphic symbols from the areas electronics, gas, water, safety technology available.
Details  More than 350 new textures ... moreyesyesyesyes
More than 350 new texturesThe texture catalog with more than 350 textures made by mtextur from the areas of asphalt, concrete, wood, HPL, ceramics, gravel, brick, plastics, metal, nature, natural stone, parquet, cobblestone, plaster, stone basket, flagstones, carpet, terrazzo

The example shows an image taken using cadvilla with textures from the areas of concrete, plaster, wood, concrete, natural stone, ceramics, gravel, asphalt, terrazzo, cobblestone, metal mesh
Details  Import and export of other 3D formats (sketchup,..) ... morenonoyesyes
Import and export of other 3D formats (sketchup,..)As of version 6, you can load other 3D formats into cadvilla in addition to the existing 3D formats, edit them right there and then save them as a cadvilla object file.

Besides the most known new 3D formats Google SketchUp and Collada, many other 3D formats can be used with cadvilla.

In detail, these additional new 3D formats are the following file names:
- Google SketchUp (*.skp)
- Collada (*.dae)
- Autodesk FBX (*.fbx)
- Luxology Modo (*.lxo)
- Cinema 4D (*c4d)
- Polygon file format (*.ply)
- Stereolithography (*.stl)
- VRML 2.0 (*.wrl, *.wrl97, *.vrml)
- DirectX (*.x)

In case you want to save specific parts of your projects as a 3D object, you can now export to one of the above mentioned 3D formats (apart from the existing 3D formats).

This option is interesting, for example, if you want to exchange data with a partner participating in your project. You simply have to agree with him on a suitable 3D file format, and your partner will be able to display the file sent to him in his own 3D program.

Especially when it comes to the 3D file formats Google SketchUp or Collada, most online portals provide access to a huge variety of up-to-date 3D objects. The majority of IKEA’s product range is, for example, available in Google SketchUp file format. On portals like 3D Warehouse , you can search for the desired objects through a search function, download them and import them in cadvilla. The use of the portal is subject of the terms of use from 3D Warehouse

The demonstration objects displayed here have been loaded from 3D Warehouse and then imported in cadvilla. The use is subject to the license terms of 3D Warehouse.

The new 3D important options and an internet connection allow you to access millions of 3D objects.
Details  Planning roof-mounting photovoltaic systems ... moreyesyesyesyes
Planning roof-mounting photovoltaic systemsAs of version 6, it’s possible to enter roof-mounting photovoltaic systems into the system. Capturing photovoltaic systems (in short: PV systems) is supported by an easy-to-use input mechanism while allowing for planning of a complete PV system within just a few minutes.

When entering the PV system, select the desired PV modules from a catalog and determine the associated parameters such as e.g. lateral spacing. In the distribution of the modules, all parameters will have an impact on the respective roof surface. When entering the data, the allocation of the module on the selected roof surface will be displayed.

After the confirmation of the proposed distribution of the PV modules with one mouse-click, the PV system will be inserted in the planning.

Now you can roughly calculate the output of the PV system via the evaluation dialog. In addition, you can obtain a parts list of the used modules with its mounting materials via the dialog based on neutral assumptions. These parts lists can then be exported and printed as an Excel, PDF or RTF document.

In case the prices for the PV module and its mounting units in the dialog are preset by the user, a rough cost calculation can be done as well.
Details  Planning flat-roof-mounting photovoltaic systems ... morenononoyes
Planning flat-roof-mounting photovoltaic systemsIn case of flat roof systems, you should determine the placing regions first. Placing regions are areas where the PV modules can be placed. Within these placing regions you can define the areas in which no PV modules must be installed.
After determining the placing regions, place the entire PV system with two mouse-clicks by simply determining the starting point of the placing using the mouse.

Afterwards, you can finalize the planning process using functions for modifying the row spacing, rotating the system (manual alignment of the modules and rows) as well as for setting a manual starting point.
Details  3D raster elements ... moreyesyesyesyes
3D raster elementsThe new function “3D raster elements” in the section “Surface planner” serves the purpose of covering surfaces (e.g. walls, floors) that should be covered with 3D elements in an evenly distributed manner as rows and columns.

Typical application areas for the function “3D raster elements” are for example facade claddings, mirror tiles, representation of floor plates in the outdoor area, wood panels, thermal insulation and many more. With just a few mouse-clicks individual walls up to entire building facades are veneered with 3D surfaces, or its terrace surface are covered with timber floor boards.

Openings in walls (e.g. window and door openings) are considered and can automatically be left out. The remaining surfaces arising from this are automatically added by partial surfaces from the 3D elements.

Profiles for the installation of the 3D elements can be created additionally and can automatically be inserted between the rows and columns. The cross-section of the profiles is selected from a pre-defined catalog or can be created on your own as well.

The created 3D surfaces can be provided individually with different textures and materials, but also in separate columns or rows.

Each included 3D element can be further divided into sub-surfaces with different dimensions and can manage its own materials.
After selecting a placing area in the 3D area of the 3D raster elements, you will receive a parts list of the placed 3D elements with the respective measurements. Identical 3D elements are added up in terms of their number and are summarized.
Details  Evaluate facade surface via context menu ... moreyesyesyesyes
Evaluate facade surface via context menuAfter the selection of an exterior wall, the context menu provides the function “Determine facade surface”.

When using this function, the software automatically identifies all exterior walls that are located exactly above and below of the selected wall and combines those to a total surface area.

This wall surface is then displayed in the following windows with a symbolic facade image. Wall openings (window and door openings) can be considered completely when determining the surface. But it’s also possible that the wall openings are only subtracted for a definable subtraction area higher than x.

Details  Output of all facade surfaces as a lis ... morenononoyes
Output of all facade surfaces as a lisThe list for the facade areas is created by a document that represents all facade surfaces of a building using a graphic for a facade view, the lengths and the width of the facade, and the gross and net surfaces (total surface area minus openings)

This list can be put out in PDF, EXCEL, HTML or RTF format.

Details  Output of all roof surfaces as a list ... morenononoyes
Output of all roof surfaces as a listThe list for the roof surfaces includes all roofs of the building with graphics and a table including the total values for the roof surfaces, the ridge length, collar length, verge length, and gutter length.

At the end of the list of roof floor spaces the individual lengths and surfaces of all the roofs used in the project are summarized.

This list can be put out in PDF, EXCEL, HTML or RTF format.
Details  Output of all 3D raster elements as a list ... morenononoyes
Output of all 3D raster elements as a listThe list for 3D raster elements is created by a document that represents the associated individual raster elements for all the previously selected raster surfaces in the form of a graphic, the number of equal elements, the description and the measurements. This list can be saved in PDF, EXCEL, HTML or RTF.
Details  Output of all window details as a list ... morenononoyes
Output of all window details as a listThe evaluation of the list for all windows contained in the project includes a representation of all windows with dimensioning and representation of the set swinging/tilting definition.

In the table mentioned below the outer dimensions, the used materials (including remarks) and the total number of each window type is included.

This list can be put out in PDF, EXCEL, HTML or RTF format.
Details  Output of additional surfaces as a list ... moreyesyesyesyes
- List of all floor spaces:

The list of all floor spaces of the building includes a list of all rooms for all floors levels with the associated floor spaces and the total surface area of the rooms of the floor level.

This list is, e.g., aimed at enabling flooring technicians to quickly determine how many square meters of parquet or carpets will be required.

- List of all wall surfaces and ceiling surfaces:

The list of wall and ceiling surfaces includes a floor-wise list of rooms with associated sidewalls and information about their lengths, heights and space.
The ceiling surface of the room is output in addition to the room description.

This list is, e.g., for paintwork in order to be able to quickly determine how much paint will be required.

Both lists can be put out in PDF, EXCEL, HTML or RTF format.
Details  Coloring 2D symbols ... moreyesyesyesyes
Coloring 2D symbolsAfter selecting a 2D symbol, the following parameters can be changed for the entire symbol in properties dialog.
- The line properties including color, line style and line width
- The filling properties of filled surfaces of the 2D symbol

This functions allows you to quickly color-adjust 2D symbols afterwards in the 2D view. For example, all electro symbols will change to gray and all water installation symbols will change to blue.

Another application option of this function would be the colored representation of the demolition and new construction of a project.

The process would be as follows:
- Select the areas for the demolition in the 2D view and save them as a 2D symbol.
- Select the areas for the new construction in the 2D view and save them as a 2D symbol.
- Insert both 2D symbols in the view, place them in the foreground and color them as desired.
- Afterwards, maybe disintegrate the symbol and delete parts of it.

Details  Additional new features and corrections ... moreyesyesyesyes
- Zooming on the cursor position has been assigned to the mouse wheel.

- Shifting up/down has been assigned to the hot key CTRL+SHIFT+mouse wheel.

(Both functions can be changed back to the default settings of the previous versions via the settings menu)

- Viewer’s standpoints can now be deleted more easily with new buttons via “3D functions/Viewer’s standpoint/Delete viewer’s standpoint”.

- The selection of a room (room text) selects the associated room text (room). Another click selects only the object clicked on.

- After renaming slides, the slide name is updated everywhere.

- The pre-setting of the graphic format for “Save view as image” is now JPG.

- The numeric post-editing of polygons via the context menu.

- Surface planner: Surfaces can be edited in 3D: Add, delete points, and shift pages in parallel, shift polygon points.

Additional features of cadvilla Version 2.x.x.x - 5.x.x.x

Additional features of cadvilla 2.x.x.x - cadvilla 5.x.x.x are listed here.